Reliability general

IEC 60529 Degrees of protection provided by enclosures (IP Code)Applies to the classification of degrees of protection provided by enclosures for electrical equipment with a rated voltage not exceeding 72,5 kV. Has the status of a basic safety publication in accordance with IEC Guide 104.
IEC 60529P Degrees of protection provided by enclosures (IP Code) - PACK including normative references
IEC 60812 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
IEC 60863 Presentation of reliability, maintainability and availability predictions
IEC 61014 Programmes for reliability growth
IEC 61025 Fault tree analysis (FTA)
IEC 61070 Compliance test procedures for steady-state availability
IEC 61078 Analysis techniques for dependability - Reliability block diagram method
IEC 61123 Reliability testing - Compliance test plans for success ratio
IEC 61124 Reliability testing - Compliance tests for constant failure rate and constant failure intensity
IEC 61160 Formal design review
IEC 61163-1 Reliability stress screening - Part 1: Repairable items manufactured in lots
IEC 61163-2 Reliability stress screening - Part 2: Electronic components
IEC 61164 Reliability growth - Statistical test and estimation methods
IEC 61165 Application of Markov techniques
IEC 61649 Goodness-of-fit tests, confidence intervals and lower confidence limits for Weibull distributed data
IEC 61650 Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities
IEC 61703 Mathematical expressions for reliability, availability, maintainability and maintenance support terms
IEC 61709 Electronic components - Reliability - Reference conditions for failure rates and stress models for conversion
IEC 61710 Power law model - Goodness-of-fit tests and estimation methods
IEC 61713 Software dependability through the software life-cycle processes- Application guide
IEC 61882 Hazard and operability studies (HAZOP studies) - Application guide
IEC 62198 Project risk management - Application guidelines

IEC 60068 - Environmental testing

IEC 60068-1 Environmental testing. Part 1: General and guidance
IEC 60068-2-1 Environmental testing - Part 2: Tests. Tests A: Cold
IEC 60068-2-2 Environmental testing - Part 2: Tests. Tests B: Dry heat
IEC 60068-2-5 Environmental testing - Part 2: Tests. Test Sa: Simulated solar radiation at ground level
IEC 60068-2-6 Environmental testing - Part 2: Tests - Test Fc: Vibration (sinusoidal)
IEC 60068-2-7 Environmental testing. Part 2: Tests. Test Ga: Acceleration, steady state
IEC 60068-2-9 Environmental testing - Part 2: Tests. Guidance for solar radiation testing
IEC 60068-2-10 Environmental testing - Part 2: Tests. Test J and guidance : Mould growth
IEC 60068-2-11 Environmental testing - Part 2: Tests. Test Ka: Salt mist
IEC 60068-2-13 Environmental testing - Part 2: Tests. Test M: Low air pressure
IEC 60068-2-14 Environmental testing - Part 2: Tests. Test N: Change of temperature
IEC 60068-2-17 Basic environmental testing procedures - Part 2: Tests - Test Q: Sealing
IEC 60068-2-18 Environmental testing - Part 2-18: Tests - Test R and guidance: Water
IEC 60068-2-20 Environmental testing. Part 2: Tests. Test T: Soldering
IEC 60068-2-21 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-27 Environmental testing. Part 2: Tests. Test Ea and guidance: Shock
IEC 60068-2-29 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
IEC 60068-2-30 Environmental testing - Part 2: Tests. Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle)
IEC 60068-2-31 Environmental testing. Part 2: Tests. Test Ec: Drop and topple, primarily for equipment-type specimens
IEC 60068-2-32 Environmental testing. Part 2: Tests. Test Ed: Free fall
IEC 60068-2-33 Environmental testing - Part 2: Tests. Guidance on change of temperature tests
IEC 60068-2-38 Environmental testing - Part 2: Tests. Test Z/AD: Composite temperature/humidity cyclic test
IEC 60068-2-39 Environmental testing - Part 2: Tests. Test Z/AMD: Combined sequential cold, low air pressure, and damp heat test
IEC 60068-2-40 Environmental testing - Part 2: Tests. Test Z/AM: Combined cold/low air pressure tests
IEC 60068-2-41 Environmental testing - Part 2: Tests. Test Z/BM: Combined dry heat/low air pressure tests
IEC 60068-2-42 Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections
IEC 60068-2-43 Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections
IEC 60068-2-44 Environmental testing - Part 2: Tests - Guidance on test T: Soldering
IEC 60068-2-45 Environmental testing. Part 2: Tests. Test XA and guidance: Immersion in cleaning solvents
IEC 60068-2-46 Environmental testing - Part 2: Tests. Guidance to Test Kd: Hydrogen sulphide test for contacts and connections
IEC 60068-2-47 Environmental testing - Part 2-47: Test methods - Mounting of components, equipment and other articles for vibration, impact and similar dynamic tests
IEC 60068-2-48 Environmental testing - Part 2: Tests. Guidance on the application of the tests of IEC 68 to simulate the effects of storage

IEC 60068-2-49 Environmental testing - Part 2: Tests. Guidance to Test Kc: Sulphur dioxide test for contacts and connections
IEC 60068-2-50 Environmental testing - Part 2: Tests. Tests Z/AFc: Combined cold/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
IEC 60068-2-51 Environmental testing - Part 2: Tests. Tests Z/BFc: Combined dry heat/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
IEC 60068-2-52 Environmental testing - Part 2: Tests - Test Kb: Salt mist, cyclic (sodium, chloride solution)
IEC 60068-2-53 Environmental testing - Part 2: Tests. Guidance to Tests Z/AFc and Z/BFc: Combined temperature (cold and dry heat) and vibration (sinusoidal) tests
IEC 60068-2-54 Environmental testing - Part 2: Tests. Test Ta: Soldering - Solderability testing by the wetting balance method
IEC 60068-2-55 Environmental testing - Part 2: Tests. Test Ee and guidance: Bounce
IEC 60068-2-57 Environmental testing - Part 2-57: Tests - Test Ff: Vibration - Time-history method
IEC 60068-2-58 Environmental testing - Part 2-58: Tests - Test Td - Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
IEC 60068-2-59 Environmental testing. Part 2: Tests. Test Fe: Vibration - Sine-beat method
IEC 60068-2-60 Environmental testing - Part 2: Tests - Test Ke: Flowing mixed gas corrosion test
IEC 60068-2-61 Environmental testing - Part 2: Test methods - Test Z/ABDM: Climatic sequence
IEC 60068-2-64 Environmental testing - Part 2: Test methods - Test Fh: Vibration, broad-band random (digital control) and guidance
IEC 60068-2-65 Environmental testing - Part 2: Methods of test - Test Fg: Vibration, acoustically induced
IEC 60068-2-66 Environmental testing - Part 2: Test methods - Test Cx: Damp heat, steady state (unsaturated pressurized vapour)
IEC 60068-2-67 Environmental testing - Part 2: Tests - Test Cy: Damp heat, steady state, accelerated test primarily intended for components
IEC 60068-2-68 Environmental testing - Part 2: Tests - Test L: Dust and sand
IEC 60068-2-69 Environmental testing - Part 2: Tests - Test Te: Solderability testing of electronic components for surface mount technology by the wetting balance method
IEC 60068-2-70 Environmental testing - Part 2: Tests - Test Xb: Abrasion of marking and letterings caused by rubbing of fingers and hands
IEC 60068-2-74 Environmental testing - Part 2: Tests - Test Xc: Fluid contamination
IEC 60068-2-75 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 60068-2-77 Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact shock
IEC 60068-2-78 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
IEC 60068-2-80 Environmental testing - Part 2-80: Tests - Test Fi: Vibration - Mixed mode
IEC 60068-2-81 Environmental testing - Part 2-81: Tests - Test Ei: Shock - Shock response spectrum synthesis
IEC 60068-2-82 Environmental testing - Part 2-82: Tests - Test Tx: Whisker test methods for electronic and electric components
IEC 60068-3-1 Environmental testing - Part 3: Background information - Section One: Cold and dry heat tests
IEC 60068-3-1A Environmental testing - Part 3: Background information - First supplement
IEC 60068-3-2 Environmental testing - Part 3: Background information - Section Two: Combined temperature/low air pressure tests
IEC 60068-3-3 Environmental testing - Part 3: Guidance. Seismic test methods for equipment
IEC 60068-3-4 Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests
IEC 60068-3-5 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
IEC 60068-3-6 Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers
IEC 60068-3-7 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
IEC 60068-3-8 Environmental testing - Part 3-8: Supporting documentation and guidance - Selecting amongst vibration tests
IEC 60068-3-11 Environmental testing - Part 3-11: Supporting documentation and guidance - Calculation of uncertainty of conditions in climatic test chambers
IEC/TR 60068-3-12 Environmental testing - Part 3-12: Supporting documentation and guidance - Method to evaluate a possible lead-free solder reflow temperature profile
IEC 60068-4 Environmental testing. Part 4: Information for specification writers - Test summaries

IEC 60068-5-2 Environmental testing. Part 5: Guide to drafting of test methods - Terms and definitions

Equipment reliability testing

IEC 60605-2 Equipment reliability testing - Part 2: Design of test cycles
IEC 60605-3-1 Equipment reliability testing. Part 3: Preferred test conditions. Indoor portable equipment - Low degree of simulation
IEC 60605-3-2 Equipment reliability testing. Part 3: Preferred test conditions. Equipment for stationary use in weather protected locations - High degree of simulation
IEC 60605-3-3 Equipment reliability testing - Part 3: Preferred test conditions - Section 3: Test Cycle 3: Equipment for stationary use in partially weather protected locations - Low degree of simulation
IEC 60605-3-4 Equipment reliability testing - Part 3: Preferred test conditions - Section 4: Test cycle 4: Equipment for portable and non-stationary use - Low degree of simulation
IEC 60605-3-5 Equipment reliability testing - Part 3: Preferred test conditions - Section 5: Test cycle 5: Ground mobile equipment - Low degree of simulation
IEC 60605-3-6 Equipment reliability testing - Part 3: Preferred test conditions - Section 6: Test cycle 6: Outdoor transportable equipment - Low degree of simulation
IEC 60605-4 Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals

IEC 60605-6 Equipment reliability testing - Part 6: Tests for the validity of the constant failure rate or constant failure intensity assumptions

ASTM Standards

B 117	Operating Salt Spray (Fog) Apparatus
B 368	Copper Accelerated acetic Acid – Salt Spray (Fog) Testing
B 827	Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests
C 1149	Specification for Self-Supported Spray Applied Cellulosic Thermal/Acoustical Insulation
C 1338	Test Method for Determining the Fungi Resistance of Insulation Materials and Facings
D 470	Crosslinked Insulations and Jackets for wire and cable
D 518	Rubber Deterioration – Surface Cracking
D 642	Test Method for Determining of Compressive Resistance Shipping Containers, Components, and Unit Loads
D 880	Test Method for Impact Testing for Shipping Containers and Systems
D 999	Vibration Testing of Shipping\Containers
D 1049	Rubber Insulating Covers
D 1149	Rubber Deterioration – Surface Ozone Cracking in a Chamber
D 1185	Test Methods for Pallets and Related Structures Employed in Materials Handling and Shipping
D 2017	Test Method for Accelerated Laboratory Test of Natural Decay Resistance of Woods
D 2059	Test Method for Resistance of Zippers to Salt Spray (Fog)
D 2344	Test Method for Apparent Interlaminar Shear Strength of Parallel Fiber Composites by Short-Beam Method
D 3273	Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings In an Environmental Chamber
D 3332	Test Method for Mechanical Shock Fragility of Products, Using Shock Machines
D 3580	Vibration (Vertical Linear Motion) Test of Products
D 3826	Practice for Determining Degradation End Point in Degradable Polyolefins Using a Tensile Test
D 3874	Ignition of Materials by Hot Wire Sources
D 4169	Performance Testing of Shipping Containers and Systems
D 4300	Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi
D 4504	Specification for Molded Polyethylene Open-Head Pails for Industrial Shipping of Nonhazardous Goods
D 4577	Test Method for Compression Resistance of a Container Under Constant Load
D 4728	Random Vibration Testing of Shipping Containers
D 4783	Test Methods for Resistance of Adhesive Preparations in Container To Attack by Bacteria, Yeast, and Fungi
D 5094	Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-style Closures
D 5112	Test Method for Vibration (Horizontal Linear Sinusoidal Motion) Test of Products
D 5276	Test Method for Drop Test of Loaded Containers by Free Fall
D 5277	Test Method for Performing Programmed Horizontal Impacts Using an Inclined Impact Tester
D 5415	Test Method for Evaluating Load Containment Performance of Stretch Wrap Materials by Vibration Testing
D 5487	Test Method for Simulated Drop of Loaded Containers by Shock Machines
D 5894	Practice for Cyclic Corrosion/UV Exposure of Painted Metal
D 6179	Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates
E 640	Test Method for Preservatives In Water-Containing Cosmetics
E 645	Test Method for Efficacy of Microbicides Used in Cooling Systems
E 875	Test Method for Efficacy of Fungal Control Agents as Preservatives for Aqueous Based Products Used in the Paper Industry
F 219	Test Methods of Testing Fine Round and Flat Wire for Electronic Devices and Lamps
F 355	Test Method for Shock-Absorbing Properties of Playing Surface Systems and Materials
F 1387	Specification of Performance of Mechanically Attached Fittings
G 7	Practice for Atmospheric Environmental Exposure of Nonmetallic Materials
G 21	Determining Resistance of Synthetic Polymeric Materials to Fungi
G 22	Determining Resistance of Plastics
G 29	Determining Algal Resistance of Plastic Films
G 53	Operating Light and Water Exposure Apparatus for Exposure of Non-Metallic Materials
G 65	Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
G 85	Modified Salt Spray (Fog) Testing

ASTM Vibration

D999-01 Standard Methods for vibration Testing of Shipping Containers D3580-95(1999) Standard Test Methods for vibration (Vertical Linear Motion) Test of Products D4728-01 Standard Test Method for Random vibration Testing of Shipping Containers
D5112-98(2003) Standard Test Method for vibration (Horizontal Linear Sinusoidal Motion) Test of Products

ASTM Shock

D3332-99 Standard Test Methods for Mechanical-Shock Fragility of Products, Using Shock Machines
D6537-00 Standard Practice for Instrumented Package Shock Testing for Determination of Package Performance

ASTM Cross Cut

D-3359 Standard Test Methods for Measuring Adhesion by Tape Test